set door production process - cleaning and maintenance of set door production process
set door (1) Low-priced paint-free door (less than 800 yuan), framed by solid wood base, hollow or filled with scraps, honeycomb paper, etc., both sides are pasted with 4mm medium-density fiberboard as a balance layer, and the surface is hand-painted with wood grain PVC film. Advantages: low price, simple production process, PVC has a certain toughness and can withstand certain impacts; Disadvantages: non-solid wood substrate, fiberboard has high formaldehyde content, is not moisture-proof, and is easy to deform. PVC paper is prone to discoloration, aging and falling off, and has a poor surface feel and matte.
(2) High-end solid wood painted door (more than 1,500 yuan), framed by solid wood substrate, solid wood finger joint material is used inside, 4mm medium density fiberboard is pasted on both sides as the balance layer, solid wood bark veneer on the surface, and the surface paint process. Advantages: Good gloss, delicate feel, solid wood base, and painted surface are not easy to fall off naturally, change color, and have high grade. Disadvantages: high price, complex process, non-wear-resistant surface of the paint, non-impact resistance, high formaldehyde content of fiberboard, balanced layer of fiberboard and solid wood bark veneer are not moisture-proof, and are prone to deformation and curl.
(3) Medium-priced composite paint door (800-1500 yuan), framed by solid wood substrate, solid wood finger joint material is used inside, 4mm medium density fiberboard is pasted on both sides as the balance layer, the surface is veneered with wood grain paper, and the surface paint process (there is no paint procedure at low prices). Advantages: relatively simple process, moderate price, good gloss, solid wood composite substrate. Disadvantages: The fiberboard has high formaldehyde content, the painted surface is not wear-resistant, and it is not impact-resistant, and it is easy to depaint and discolor; the fiberboard balance layer and wood grain paper veneer are not moisture-proof, and it is easy to deform and curl. Cleaning and Maintenance of
Set Door Materials are mainly divided into walnut, cherry wood, sabilie, mahogany, maple, teak, ebony, rosewood, crape myrtle, zebra, oak, ellipse, ash, mahogany, etc. When cleaning, you can use soft, monotonous cotton cloth or silk to wipe it. Wiping with hard or hard media may scratch the surface; if there is serious stain on the door panel of the indoor suit door, we can use neutral cleaning agents or furniture-specific cleaning agents, clean up the stains first, and then dry wipe them. But it is important not to wash it with clean water.
The doors of home furnishings are frequently used and are easily damaged. If you can think more about it and master some tips on maintenance, it can bring convenience to life.
1. Self-made elastic door block: The doors of the home often need to be opened and closed. When the door is opened, it often directly hits the wall. Over time, the lock box and handle on the door will easily hit the wall, damaging the wall and door, affecting the beauty. You can find a rubber block about 5 cm thick or nail a thick rubber on a small wooden block and nail it to the lower corner of the inner side of the door against the hinge side, so that the door and window will not be damaged.
2. Keep the door from being blown open by the wind: If the door in the home is easily blown open by the wind or open without opening after the door is closed, it is both inconvenient and unsafe. You can find a powerful magnet of appropriate size and buried it flat above the door frame about 1/4 of the height of the door, and then nail a piece of iron sheet to the place where the door leaf and the door frame match. After closing the door, it will suck each other to prevent the door from being blown open by the wind. This method can also be used for cupboards, wardrobes, windows, etc.
3. Anti-stick door lock: After using the munition door lock for a long time, it will often become dry and unficient, making it difficult to open and close. In this case, you can drop some engine oil on both sides of the movable lock or wipe it with soap a few times. The door lock will be flexible and flexible, and it will be open and closed freely.